PROCOOL Professional Cooling Solutions

Description
Specifications
More Info
Reviews

The PROCOOL AVP-180T is a temperature controlled, variable speed silent fan system.

One 80mm Thermistor controlled fan speeds up as heat increases and will slow down as heat decreases.
The fan controller starts and stops the fan(s) at user defined setpoints.
Expandable up to 8 fans.

With a noise level of only 6-14 dBA at top speed, the AVP-180T is the quietest fan system available.
The low noise makes this system suitable for noise sensitive applications from home AV to professional studios.
And with airflow pushing at 14-32 CFM this system can cool most cabinets.

AVP-180T Includes:

✓ Fan Controller
✓ Controller shelf mount
✓ 1 SXT80 Temp controlled fan
✓ 1 Fan Grill w/screws
✓ Power supply

✓ Quiet operation - 6-14 dBA
✓ High Airflow - 14-32 CFM
✓ 3 Year Warranty

Procool Fan Model SXT80:

Procool model SXT80 fans are Silent temperature controlled variable speed 80mm fans.
The specially designed blade and motor allow maximum airflow with the lowest noise.

Speeds range from 1200 RPM idle start speed to 2400 RPM at full speed.

SXT80 fans have a thermal sensor that detects the temperature and tells the fan how fast to run. The sensor should be located on or near the heat source for optimal performance.

When the sensor detects heat above 77°F the fan speed will begin to increase.The fan will reach full speed of 2400 RPM at 104°F.

SXT80 Data Sheet.pdf

Fan Controller:

User sets the controller's on and off temps to start and stop the system. Set a Global temp that will control all 4 fans together and/or set individual temps for each fan.
Each of the 4 fan power connectors are numbered 1 thru 4 corresponding to the front panel LED indicators. When the LED's are on that fan will be on. When the LED's are off those fans will be off.
Global setting: Front panel LED's for fans 1-4 are all on.
Individual setting: Front panel LED on for the selected or operating fans.

Typical start temp is about 80-85F. Off temp at or slightly above room temp. These settings can be adjusted for optimal performance. The controller has a temp sensor that should be located on or near the heat source, or can be located at the top of the cabinet for an ambient reading. This temp is displayed on the controller during operation for easy monitoring. Or, the display can be shut off during operation. (See Operating instructions)

Programming Temperature profiles:

Set the Global range higher than individual fan settings. If the highest individual temp is for example 90F set the Global temp to 92F or higher. If the Global temp is set to start at 85F then any fans set to start at 90F they will start when the Global start point of 85F is reached. Likewise if using the Global setting, make sure all individual settings are set outside of the Global range. The same rule applies for the OFF settings.

See Operating Instructions for more details

Fan Controller Operating Instructions.pdf

Mount:

A shelf mount is included. Use to mount the controller under a shelf or top of the cabinet.
Optional wall mount and 1U rack mount are also available.

Power Supply Model PSW-12V2A

Input: 100-240 VAC
Output: 12VDC
AC plug type: NEMA 1-15P
DC Cable: 36 inch with 2.1mm barrel plug

Fans:	1	Air Pressure Chart Thermistor Speed Chart


Fan Size:	80mm x 80mm x 25mm
Fan Speed:	1200-2400 RPM
Air Flow:	14-32 CFM
Noise:	6-14 dBA
Bearings:	FDB, fluid dynamic bearings
Fan Thermistor wire length:	24"
Controller Thermal Probe length:	30" (48" available)
Power Supply:	100-240 VAC - 12 VDC
Power Supply Cable length:	36"
Power Supply Plug Type:	NEMA 1-15P
Current draw:	0.17A
Power consumption:	2.04w
Grills/Guards:	Black Wire
Fan Model SXT80 data sheet	AVP-MFC Operating Instructions.pdf

Installation Instructions

Fan Mounting Instructions.pdf

Operating Instructions

AVP-180T- Operating Instructions.pdf

Care and Maintenance

To maintain optimal performance, keep the fans clean. Canned air works well. If the fans are used outdoors or in a dusty environment is recommended to clean the fan blades as needed to keep clean.

Blade Removal

For cleaning and maintenance, the blade prop can be removed.
Grasp the blade prop and pull straight out of the fan body. Inspect the shaft and lubricate if needed. Any oil will work; light grease works best. Clean blade as needed with a dry cloth. Soap and water can be used if needed, but should be thoroughly rinsed and dried before use. Reinstall the blade; when properly installed the blade will snap into place.

Troubleshooting

The fan will not start:

1. Is the controller display on? If Yes, skip to #3.
2. Check the power connections. The power supply has a green led indicator, it should be on. If it is not check the power source. If not lit or flashing, it would indicate power supply failure or no power source power.
3. Check that the fan plugs are all plugged in on the back of the controller.
4. Check the fan blades to make sure they are fully seated in the housing. Press on the center of the blade and push in. If it is not seated you can hear it snap into place.
5. Turn the fan blade by hand to see if they are stuck. They should be free moving. If this starts the fan it is likely the fans need maintenance.
6. When the fans are new and if the temp is below 70?F the thermistor probe may need to be warmed by hand slightly to get the fan to spin.

The fan is making noise:

1. Check for anything that could be rubbing against the fan blade.
2. Make sure the fan blades are clean. Dirty fan blades can make noise.
3. Check the blade prop shaft for lubrication. (See Blade Removal above)

If the above steps do not solve the problem, contact our friendly customer service for assistance.

Customer Reviews

0 / 0 Reviews

Be the first to review this fan.

SAMPLE REVIEWS

Reviewed By: Jimmy on May 23rd 2016

The best rack cooling fan I've ever owned.

Reviewed By: John on May 24th 2016

Keeps my rack cool and is absolutely silent.

PROCOOL AVP-180T Review
Name *
First Name Last Name
E-mail *
Phone Number
- Area Code Phone Number
Order Number
Review *
Comments
Privacy Options *

Post review with my first name only. Post my review as "Anonymous"
Should be Empty:

Frequently purchased with this item
Plug Adaptors Converts NEMA 5-15R to IEC320 C14 Use to connect all Procool power supplies to C13 receptacle. Length = 12 inches Part No. PSA-C14	AV-Y6 6" Fan power "Y" Splitter Add additional fans	Replacement Fans Replacement 40mm and 80mm fans

Procool AVP-180T

Temperature controlled Variable Speed Silent Fan System

Need it fast?
Need a large quantity?
Call or email us for a quote.

The PROCOOL AVP-180T is a temperature controlled, variable speed silent fan system.

Procool Fan Model SXT80:

Fan Controller:

Mount:

Power Supply Model PSW-12V2A

Installation Instructions

Operating Instructions

Care and Maintenance

Blade Removal

Troubleshooting

The fan will not start:

The fan is making noise:

Customer Reviews

PROCOOL AVP-180T Review

Frequently purchased with this item

Procool AVP-180T

Temperature controlled Variable Speed Silent Fan System

Need it fast? Need a large quantity? Call or email us for a quote.

The PROCOOL AVP-180T is a temperature controlled, variable speed silent fan system.

Procool Fan Model SXT80:

Fan Controller:

Mount:

Power Supply Model PSW-12V2A

Installation Instructions

Operating Instructions

Care and Maintenance

Blade Removal

Troubleshooting

The fan will not start:

The fan is making noise:

Customer Reviews

PROCOOL AVP-180T Review

Frequently purchased with this item

Need it fast?
Need a large quantity?
Call or email us for a quote.